咨詢熱線

13905418708

一材質要求：

Material requirements:

路沿石石料采用質地均勻的天然麻石機械切削加工而成，石材的強度必須合格，要求其色澤均勻，表面無裂紋，棱角完整，外觀一致，無明顯斑點色差，不允許有風化現象，裝卸時不準摔砸撞碰，以免造成損傷。

The roadside stone material is made of natural hemp stone with uniform texture by mechanical cutting and processing. The strength of the stone must be qualified, and its color must be uniform, with no cracks on the surface, complete edges and corners, consistent appearance, no obvious spots or color differences. Weathering is not allowed, and it is not allowed to be dropped or bumped during loading and unloading to avoid damage.

二加工要求：

2. Processing requirements:

按統一長度進行下料，外露面必須機切拋光，長度允許誤差在±20mm范圍內，寬度厚度高度允許誤差在±2mm范圍內。

Cutting should be carried out according to a uniform length, and the exposed surface must be machine cut and polished. The allowable error in length is within ± 20mm, and the allowable error in width, thickness, and height is within ± 2mm.

三施工要求：

Three construction requirements:

路沿石必須掛通線進行施工,按側平面頂面示高標線繃緊，按線碼砌側平石，側平石要安正，切忌前仰后合，側面頂線順直圓滑平順，無高低錯牙現象，平面無上下錯臺內外錯牙現象。

The roadside stones must be constructed with a hanging line, and the elevation line indicated on the top surface of the side plane should be tightened. The side flat stones should be built according to the line code, and the side flat stones should be upright. It is important to avoid leaning forward and backward. The side top line should be straight, smooth, and smooth, without any high or low misalignment, and there should be no upper or lower misalignment inside or outside the plane.

路沿石必須座漿砌筑，座漿必須密實，嚴禁塞縫砌筑。

The roadside stones must be built with mortar, and the mortar must be dense. It is strictly prohibited to build with gaps.

路沿石接縫處錯位不超過1mm；側石和平石必須在中間均勻錯縫。

The misalignment at the joint of the curbstone shall not exceed 1mm; The side stones and flat stones must be evenly staggered in the middle.

路沿石側平石應保證尺寸和光潔度滿足設計要求，外觀美觀，對彎道部分側石應按設計半徑專門加工彎道石，砌筑時保證線形流暢圓順拼縫緊密，弧形側石必須人工精鑿后拋光處理。

The side flat stones along the roadside should ensure that the size and smoothness meet the design requirements, and the appearance is beautiful. For the side stones in the curved section, they should be specially processed according to the design radius. When laying, the linear shape should be smooth, round, and the joints should be tight. The curved side stones must be manually chiseled and polished.

路沿石后背應還土夯實，夯實寬度不小于50mm，厚度不小于15mm。

The back of the curbstone should be compacted with soil, with a compaction width of no less than 50mm and a thickness of no less than 15mm.

路沿石勾縫：勾縫時必須再掛線，把側石縫內的雜物剔除干凈，用水潤濕，然后用1：2.5水泥砂漿灌縫填實勾干。

Road edge stone pointing: When pointing, a line must be hung again to remove debris from the side stone joints, moisten them with water, and then fill and dry the joints with 1:2.5 cement mortar.

側平石勾縫安砌后適當澆水養護。

After the installation of the side flat stone joint, water and maintain it appropriately.